by admin

Cisco 3850 Power Supply Slots

Cisco 3850 Power Supply Slots Rating: 3,4/5 6127 reviews

The Cisco Catalyst 3850 Series Switches support full IEEE 802.3at Power over Ethernet Plus (PoE+), Cisco Universal Power over Ethernet (Cisco UPOE), modular and field-replaceable network modules, RJ45 and fiber-based downlink interfaces, and redundant fans and power supplies. Cisco 3750 Series Power Supplies. Due to the Christmas holiday for UPS, ground orders placed 12/24 & 12/25 will be shipped on Monday, 12/28.

It is sometimes confusing on which interfaces are available and which can be configured when using one of the NM modules in a Cisco 3850 Switch. We currently offer three different modules:

  • C3850-NM-4-10G Cisco 3850 Series 4 x 10GE Network Module L-C3850-48-S-E= C3850-48 IP Base to IP Services Electronic RTU License PWR-C1-715WAC Cisco 3850 Series Power Supply 715W AC PWR-C1-715WAC/2 Cisco 3850 Series Secondary Power Supply 715W AC Config 1 Secondary Power Supply CAB-SPWR-30CM Catalyst 3750X and 3850 Stack Power Cable 30 CM.
  • Cisco StackPower unifies the individual power supplies installed in the switches and creates a pool of power, directing that power where it is needed. Up to four switches can be configured in a StackPower stack with the special connector at the back of the switch using the StackPower cable, which is different than the StackWise-480 cables.

C3850-NM-4-1G (four 1-Gigabit SFP module slots)

Supply

C3850-NM-2-10G (Combination of 1-Gig and 10-Gig ports)

C3850-NM-4-10G (four 10-Gigabit slots or four 1-Gigabit slots)

The available configuration is based on which model NM you are using. The intent of this document is to help clear up some of the misunderstood configuration options. Below are details on each NM module and how to configure each one when inserted into the switch.

C3850-NM-4-1G:

This module has four 1-Gigabit SFP module slots. Any combination of standard SFP modules are supported. SFP+ modules are not supported. If you insert an SFP+ module in the 1-Gigabit network module, the SFP+ module does not operate, and the switch logs an error message.

C3850-NM-2-10G:

Cisco 3850 power supply slots download

This module has four slots that support the following combinations:

• Two slots (left side) support only 1-Gigabit SFP modules and two slots (right side) support either 1-Gigabit SFP or 10-Gigabit SFP modules.

Cisco 3850 Power Supply Slots Game

• Three slots (left side) support 1-Gigabit SFP modules and one slot (right side) supports 10-Gigabit Ethernet SFP+.

Supported combinations of SFP and SFP+ modules:

• Slots 1, 2, 3, and 4 populated with 1-Gigabit SFP modules.

• Slots 1 and 2 populated with 1-Gigabit SFP modules, and Slot 4 populated with one 10-Gigabit SFP+ module.

• Slot 3 and Slot 4 each populated with 10-Gigabit SFP+ modules.

C3850-NM-4-10G:

Cisco 3850 Power Supply Slots For Sale

This module has four 10-Gigabit slots or four 1-Gigabit slots.

Note: This is only supported on the 48-port models.

Sale

Configuration:

For the C3850-NM-4-1G module – All ports are natively Gig and are configured as Gig1/1/1 through Gig1/1/4

<snippet>

interface GigabitEthernet1/1/1 <——– Config this interface
!
interface GigabitEthernet1/1/2 <——– Config this interface
!
interface GigabitEthernet1/1/3 <——– Config this interface
!
interface GigabitEthernet1/1/4 <——– Config this interface
!
interface TenGigabitEthernet1/1/1 <——– Disregard
!
interface TenGigabitEthernet1/1/2 <——– Disregard
!
interface TenGigabitEthernet1/1/3 <——– Disregard
!
interface TenGigabitEthernet1/1/4 <——– Disregard

Supply

For the C3850-NM-4-10G module – All ports default to 10G and should be configured as
TenGig1/1/1 through TenGig1/1/4 – even though you are operating them as 1G via SFPs.

<snippet>

Cisco 3850 Power Supply Slot B

interface GigabitEthernet1/1/1 <——– Disregard
!
interface GigabitEthernet1/1/2 <——– Disregard
!
interface GigabitEthernet1/1/3 <——– Disregard
!
interface GigabitEthernet1/1/4 <——– Disregard
!
interface TenGigabitEthernet1/1/1 <——– Config this interface
!
interface TenGigabitEthernet1/1/2 <——– Config this interface
!
interface TenGigabitEthernet1/1/3 <——– Config this interface
!
interface TenGigabitEthernet1/1/4 <——– Config this interface

For the C3850-NM-2-10G module – The first two ports are natively 1G ports and the last two ports are natively 10G ports. So you configure the 1Gig ports as Gig1/1/1 through Gig1/1/2, and configure the last two ports as TenGig1/1/3 through TenGig1/1/4 – even if you are operating the last two ports as 1G.

## This is commonly misunderstood ##

<snippet>

interface GigabitEthernet1/1/1 <——– Config this interface
!
interface GigabitEthernet1/1/2 <——– Config this interface
!
interface GigabitEthernet1/1/3 <——– Disregard
!
interface GigabitEthernet1/1/4 <——– Disregard
!
interface TenGigabitEthernet1/1/1 <——– Disregard
!
interface TenGigabitEthernet1/1/2 <——– Disregard
!
interface TenGigabitEthernet1/1/3 <——– Config this interface even if using 1G
!
interface TenGigabitEthernet1/1/4 <——– Config this interface even if using 1G

** There are only 4 interfaces which are valid and the other 4 should not be used even though they still show up in the CLI

Supported GBICs:

TenGig

Cisco 3850 Power Supply Slots Download

  • SFP-H10GB-CU1M
  • SFP-H10GB-CU3M
  • SFP-H10GB-CU5M
  • SFP-10G-SR
  • SFP-10G-LRM
  • SFP-10G-LR
  • SFP-10G-ER

OneGig

  • GLC-T (10/100/1000)
  • GLC-SX-MM
  • GLC-LH-SM
  • GLC-SX-MMD
  • GLC-LH-SMD
  • GLC-ZX-SM
  • GLC-ZX-SMD
  • GLC-BX-D
  • GLC-BX-U
  • CWDM SFP
  • SFP-GE-S
  • SFP-GE-L
  • SFP-GE-Z
  • DWDM SFP
  • DWDM SFP (add.)

Reference:

Installing a Network Module

10-Gigabit Ethernet Transceiver Modules Compatibility Matrix

Cisco Gigabit Ethernet Transceiver Modules Compatibility Matrix

Original Doc you can refer to: https://supportforums.cisco.com/docs/DOC-36084

More Cisco Switch Topics: